Difference between revisions of "Checklist"
From NavykI
(New page: == Propulsion == *engine - brand and type *gearbox - brand and type *s t u w d r u k l a g e r) |
|||
| (9 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | == Systems general == | ||
| + | *what is the function/purpose of this item? | ||
| + | *is it necessary? | ||
| + | *is the size right? | ||
| + | *is the material right? | ||
| + | *is the fitting of adequate strength? | ||
| + | *can it be fitted easily? | ||
| + | *where should it be manufactured? | ||
| + | *where should it be fitted? | ||
| + | *are the terminal points adequately defined? | ||
| + | *what is the maintenance and repair required? | ||
| + | *should it be maintained on board? | ||
| + | *is there adequate access for maintenance? | ||
| + | *should it be removed for replacement? | ||
| + | *can the unit be taken out for replacement? | ||
| + | *what spares are required? | ||
| + | *see [http://www.managingboatbuilding.com Managing Boat Building] | ||
| + | |||
== Propulsion == | == Propulsion == | ||
| − | *engine | + | *engine ''brand and type'' |
| − | *gearbox - brand and type | + | *gearbox ''brand and type'' |
| − | * | + | *thrust bearing ''brand and type'' |
| + | *shaft inner bearing ''brand and type'' | ||
| + | *shaft tube ''OD'' | ||
| + | *minimum distance between forward shaft tube bearing and thrusterbearing is shaft diameter -9 x 20 (Exalto) | ||
| + | |||
| + | == Cut outs == | ||
| + | *doors ''brand and type'' | ||
| + | *portholes ''brand and type'' | ||
| + | *windows ''brand and type'' | ||
| + | *hatches ''brand and type'' | ||
| + | *bow thruster ''brand and type'' | ||
| + | *stern thruster ''brand and type'' | ||
| + | *rudder tube ''OD'' | ||
| + | *anchor arrangement | ||
| + | *ventilation engine room | ||
| + | *gas locker | ||
| + | *deck fills: | ||
| + | **fuel fill | ||
| + | **fresh water fill | ||
| + | **waste water suction | ||
| + | *scuppers | ||
| + | *freeing ports | ||
| + | |||
| + | [[Category: Marine Engineering]] | ||
Latest revision as of 08:29, 14 November 2012
Systems general[edit]
- what is the function/purpose of this item?
- is it necessary?
- is the size right?
- is the material right?
- is the fitting of adequate strength?
- can it be fitted easily?
- where should it be manufactured?
- where should it be fitted?
- are the terminal points adequately defined?
- what is the maintenance and repair required?
- should it be maintained on board?
- is there adequate access for maintenance?
- should it be removed for replacement?
- can the unit be taken out for replacement?
- what spares are required?
- see Managing Boat Building
Propulsion[edit]
- engine brand and type
- gearbox brand and type
- thrust bearing brand and type
- shaft inner bearing brand and type
- shaft tube OD
- minimum distance between forward shaft tube bearing and thrusterbearing is shaft diameter -9 x 20 (Exalto)
Cut outs[edit]
- doors brand and type
- portholes brand and type
- windows brand and type
- hatches brand and type
- bow thruster brand and type
- stern thruster brand and type
- rudder tube OD
- anchor arrangement
- ventilation engine room
- gas locker
- deck fills:
- fuel fill
- fresh water fill
- waste water suction
- scuppers
- freeing ports
