Difference between revisions of "15012 pontoon AMS"
From NavykI
| Line 8: | Line 8: | ||
**2 coupling winches at aftdeck, minimum 500mm from boat side, about 10 ton per winch | **2 coupling winches at aftdeck, minimum 500mm from boat side, about 10 ton per winch | ||
**hatches of sufficient size for each compartment with coaming 500mm height | **hatches of sufficient size for each compartment with coaming 500mm height | ||
| + | |||
*Suction box | *Suction box | ||
| Line 13: | Line 14: | ||
**suction box to have removable water inlet grills | **suction box to have removable water inlet grills | ||
**idea is to have a box which can be lowered beneath the bottom with 2 worm winches | **idea is to have a box which can be lowered beneath the bottom with 2 worm winches | ||
| + | |||
*Railing and safety | *Railing and safety | ||
| Line 18: | Line 20: | ||
**deck to have non skid strips | **deck to have non skid strips | ||
**everything conform regulations | **everything conform regulations | ||
| + | |||
*Container(s) | *Container(s) | ||
Revision as of 11:59, 10 March 2015
- Pontoon to be suitable for use in oil ports (regulations)
- Construction
- width to be extended by 2m at CL
- deck load 2 ton/m2 minimum
- aftship to have recess for receiving bow of pushboat
- 2 coupling winches at aftdeck, minimum 500mm from boat side, about 10 ton per winch
- hatches of sufficient size for each compartment with coaming 500mm height
- Suction box
- water intake box for fifi container suitable for flow rate 23m3/minute
- suction box to have removable water inlet grills
- idea is to have a box which can be lowered beneath the bottom with 2 worm winches
- Railing and safety
- at longitudinal sides a horizontal pipe Ø80-100 thickwalled, about 150mm above deck, stanchions every 1500mm, on top of it the railing, total height to be 1m
- deck to have non skid strips
- everything conform regulations
- Container(s)
- twistlocks and subframes for 2 container units of 5.50m, placed transverse on deck of pontoon
- frames for containers and generator to be heavy and with flexible mounts, if necessary with reinforced construction below deck, to avoid pontoon becoming a resonance box.
- Fuel tanks
- total capacity 9 ton
- 2 tanks H1000, W1500, length to be determined by Navyk
- crossover
- tanks to have a gauge glass
- tanks to have a BOBS system (X-BOB)
- fill station conform regulations
- Mooring and anchoring
- 2 bollards at every corner (I suggest we keep existing 6 bollards)
- bollards to be non skid (by means of welding points)
- bollards to be checked with regulations (reinforcement required below deck?)
- fenders - at deck edge eyes for mounting car tires (see example drawings)
- off center electric anchor winch with wire
- anchor to be stored at deck
- winch to match regulations
- Name and colors
- colorscheme
- RAL3020 red
- RAL9005 black
- RAL7015 grey
- RAL1018 yellow
- name and buildnumber on pontoon (name P.A. 14?)
- colorscheme
- Electric
- generator set 15kVA on deck
- shore connection
- Bilgesystem conform class
- Masts and lights
- 2x mast off center at each end
- decklights for save working during night
- nav lights + daylight signals for anchor and sailing conform BPR
- 2x decklight at upper container edge
Drawing list
- general arrangement
- construction drawing
- deck plan
- water suction box
- foundation plan fifi unit and generator
- fuel tanks, piping and fill station
- bilge pumps
- masts and lighting
- pushboat recess details (integrate in construction drawing?)
- e-box / shore connection plan?
