Difference between revisions of "15038 Bestevaer 45 ST Pure"

Revision as of 15:42, 15 July 2015

'Pure' is the name of new line of yachts, of which the first boat is named 'Nescio'. This first boat will be build for Eeuwe Kooi himself (owner/director KMY).

TO DO

General

• hatch coamings + Sky screens (Ocean air)
• port hole boxes superstructure
• leather ceilings
• lining > V-grooves, every 100mm, parallel to deckline/sheer
• access bolt connection for mounting superstructure
• drill holes and notches for assembly
• heating > add bulkhead penetrations for hose and grills
• FYI > solid corner profiles in furniture plintes will be painted white
• locker shelves > mounted with shelf supports (Hettich)
• sole > add hatches in combination with making the alu sole supports
• labels > create excel sheet with codes for each part
• ceilings > leather panels will be mounted with Fastmount
• hatches and portlights
  • Deckhatches:
    • Lewmar Size 60 low profile: 39960030
    • Lewmar Size 30 low profile: 39930030
  • Portligths in superstructure:
    • Lewmar Standard portlight Size 3: 393320200
  • Portlights in cockpit:
    • Lewmar Standard portlight Size 5: 393520200

Fore Cabin

• hatches in bed bottom > modify in way of batteries
• hatches bow thruster > enlarge
• shelf > add against FWD bulkhead, 300 deep, 650 from bed bottom
• shelf > add against AFT bulkhead, in corner with lining (for phone, etc)
• high lockers > move upper plinth outboard with 200mm
• shelf locker > move side panel 100mm forward
• porthole SB > relocate in middel of lining
• porthole PS > relocate? KMY
• shelf SB > rotate profile 10 degrees, move outboard to 10mm distance from vertical solid profile of shelf locker, make locker with doors under
• bed > make bulkhead in storage, forward of batteries
• bed > add bracket under each battery up to sole

Salon

• pillar mast bulkhead > connected with FB 8mm, split mast bulkhead
• table
• chain plate reinforcement > mask
• lower hinge in forward upper cabinet will be solved by KMY
• counter top > raise 100mm
• add shelf profile between upper lockers
• box against FWD bhd > bottle storage, make narrower, add hatch in counter top (with fingerhole)

Galley

• pillar behind removable side
• re-arrange front drawers to avoid collision with table
• fridge > mvoe down, drawer above fridge
• fridge > ventilation by holes in locker bottom next to plinth and holes in upper part of PS counter side (NO grill)
• countertop > raise 50mm
• shelf > add 1 or, if possible, 2 shelves between upperlockers. For spices, etc. Deep about 60mm and a high shelf profile of about 70mm
• upper lockers > LED lights behind solid profile? KMY
• drawers > use standard Hettich drawers where possible
• drawers in galley fore side > various heights, top about 80mm, second drawer about 200, third drawer about 300

Bathroom

• sole detail
• yard will inform if glass doors in bathroom will be applied or not
• material > panels can be normal HPL as rest of boat, the special quality W400-VV is canceled.
• entrance door > rotates outside and forward
• black water tank > 50 liter, behind toilet (shape to be determined by Navyk)
• glass doors > yard to decide to apply or not

Aft cabins

• PS > bulkhead cutout, profiles, raise horizontal profile in line with sole deckhouse
• bed bottoms > hatches for access storage space under, support?
• lining > align knuckles with V-grooves
• entrance door > rotates inside
• technical space > add access hatches in longitudinal panels

Deck house

• 'pillar boxes' to be moved outboard 10mm
• 'pillar boxes' add recesses for technical panels, dimensions? KMY
• all panels to be white, except for bench fronts, 'pillar boxes' besides entrance and top of guest cabin SB
• bench fronts and top of guest cabin to be covered with 6mm bamboo as for entrance doors
• add solid profiles around top of guest cabin.
• WJ will provide correct model of entrance
• add solid profiles at vertical corners of transition salon/guest cabin to deck house
• stairs > add solid profile to vertical corner of lower step
• recess behind seats > about 50 wide, 100 deep
• lining besides entrance > add solid profile at vertical (skewed) corner
• benches > seat width 550mm
• benches > back inclinated
• benches > raise bottom? KMY
• Aft cabin lining > reduce lost space behind lining
• Stair steps > use for storage (3 steps)
• Aft cabin top > removable plexiglass panel for light and air, detail? KMY
• PS bench > remove armrest, make suitable for transverse seating
• bed bottoms > raise 100mm for additional storage and wider matrass
• bed bottoms > hinged hatch
• bed PS > large drawer under

Sheet estimation

transverse grain

• 17mm single bamboo - 3 sheets - bench fronts SL / galley front / table sides
• 6mm single bamboo - 1 sheet - bench fronts DH

People

• Eeuwe Kooi - director/owner (not directly involved)
• Willem Berends - chain manger (responsible for contract)
• Willem-Jan van der Vegt - engineer (our contactperson)
• Haaie Andringa - foreman carpentry

Exchange work

• KMY negotiated €1.000 discount for delivering a 3D model of interior - send file is only a block file
• integration of heater ducting is not in contract
• info is not delivered on Monday, June 15 but came partially on June 16 and 17

As discussed

July 1, 2015

• furniture doors - 17mm is OK
• entrance hatch recess box - PUR insulated, put plywood panel in front
• stair steps solid wood
• cockpit sole - covered with cork 9mm
• lining - leather panels are canceled
• porthole boxes - yard makes tube, out of our delivery

June 16, 2015

• black water tank - to be determined by Navyk, volume around 50 liter, position SB behind toilet

June 11,2015

• tolerances
  • vertical:
    • sole to supporting structure - 0mm
    • ceiling to structure - 0mm
  • horizontal
    • clearance from inner frame contour - 20mm (space between frames is reserved for systems)
• insulation type is PUR
• grain orientation will be vertical
• sole supports are alu tube 50x30x?
• cabinet interiors to be white
• KMY workshop facilities:
  • no veneer press
  • edge band machine for straight edges
  • lamello machine
  • round router bits R6, R8, R10, R12
• Navyk will route the ducting for airheating through the interior
• Navyk is free to use their own material naming
• Navyk will give a price offer for the aluminium sole supports

Structure model - modifications!

• Forepeak bulkhead - stiffeners will be on aft side (cabin side)
• Pilothouse - between the windows will be a vertical T-profile with a web of 50x6 and a flange of 50x8
• Entrance door forecabin - to be determined by Navyk, it will be a joinery door, not an aluminum door
• sole structure - to be determined, Navyk will make a price offer for this