Difference between revisions of "Material Properties"
From NavykI
Navykisysop (talk | contribs) |
m (Steven moved page Material Prorperties to Material Properties) |
||
| (13 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| + | == Steel == | ||
| + | |||
| + | *Density 7800 kg/m3 | ||
| + | |||
| + | |||
== Stainless steel == | == Stainless steel == | ||
| Line 51: | Line 56: | ||
|- | |- | ||
|} | |} | ||
| + | |||
| + | *Quality 304 (A2) and 316/316L (A4) are suitable for use on board. | ||
| Line 58: | Line 65: | ||
*5083-H111 can be bended without restrictions | *5083-H111 can be bended without restrictions | ||
*5083-H321 limited bending (no hard bigger than 45 degrees) | *5083-H321 limited bending (no hard bigger than 45 degrees) | ||
| − | + | http://asm.matweb.com/search/SpecificMaterial.asp?bassnum=MA5083H32 | |
==Diesel== | ==Diesel== | ||
| Line 66: | Line 73: | ||
==Gasoline== | ==Gasoline== | ||
*Density 720 kg/m3 | *Density 720 kg/m3 | ||
| + | |||
| + | ==Carbon steel diamond plate == | ||
| + | |||
| + | {| | ||
| + | |Th | ||
| + | |Diamond plate | ||
| + | |Normal plate | ||
| + | |Diamond % heavier | ||
| + | |- | ||
| + | |mm | ||
| + | |Kg/m^2 | ||
| + | |Kg/m^2 | ||
| + | |- | ||
| + | |3 | ||
| + | |26.17 | ||
| + | |23.40 | ||
| + | |10.6% | ||
| + | |- | ||
| + | |4 | ||
| + | |34.91 | ||
| + | |31.20 | ||
| + | |10.6% | ||
| + | |- | ||
| + | |4.5 | ||
| + | |36.91 | ||
| + | |35.10 | ||
| + | |4.9% | ||
| + | |- | ||
| + | |5 | ||
| + | |43.60 | ||
| + | |39.00 | ||
| + | |10.5% | ||
| + | |- | ||
| + | |6 | ||
| + | |48.68 | ||
| + | |46.80 | ||
| + | |3.9% | ||
| + | |- | ||
| + | |8 | ||
| + | |64.40 | ||
| + | |62.40 | ||
| + | |3.1% | ||
| + | |- | ||
| + | |10 | ||
| + | |80.12 | ||
| + | |78.00 | ||
| + | |2.6% | ||
| + | |- | ||
| + | |12.5 | ||
| + | |99.70 | ||
| + | |97.50 | ||
| + | |2.2% | ||
| + | |- | ||
| + | |} | ||
| + | |||
| + | *Quality 304 (A2) and 316/316L (A4) are suitable for use on board. | ||
| + | |||
| + | == Lead == | ||
| + | |||
| + | *Density 11340 kg/m3 | ||
| + | |||
| + | == Timber == | ||
| + | source 'Hout Vademecum' | ||
| + | *birch 660 kg/m3 | ||
| + | *ocoume 420 kg/m3 | ||
| + | *poplar 435 kg/m3 | ||
| + | *teak 675 kg/m3 | ||
| + | *MDF 750 kg/m3 | ||
| + | |||
| + | == Plywood == | ||
| + | See [[Plywood]]. | ||
| + | |||
| + | |||
[[Category: Materials]] | [[Category: Materials]] | ||
Latest revision as of 09:25, 20 December 2017
Contents
Steel[edit]
- Density 7800 kg/m3
Stainless steel[edit]
| Property | Units | Typical | Type 316 | Type 316L |
| Ultimate Tensile Strength | [N/mm^2] | 586 | 517.1 min | 482.6 min |
| 0.2% Offset Yield Strength | [N/mm^2] | 303.37 | 206.84 min | 172.37 min |
| Elongation in 2 inches | [%] | 56 | 40 min | 40 min |
| Reduction in Area | [%] | 69 | — | — |
| Hardness, Rockwell | [B] | 81 | 95 max | 95 max |
| Density | [Kg/m^3] | 7 888.77 | — | — |
| Modulus of Elasticity | [psi] | 29 x 10^6 | — | — |
- Quality 304 (A2) and 316/316L (A4) are suitable for use on board.
Aluminum[edit]
- Density 2700 kg/m3
- 5083-H111 can be bended without restrictions
- 5083-H321 limited bending (no hard bigger than 45 degrees)
http://asm.matweb.com/search/SpecificMaterial.asp?bassnum=MA5083H32
Diesel[edit]
- Density 850 kg/m3
Gasoline[edit]
- Density 720 kg/m3
Carbon steel diamond plate[edit]
| Th | Diamond plate | Normal plate | Diamond % heavier |
| mm | Kg/m^2 | Kg/m^2 | |
| 3 | 26.17 | 23.40 | 10.6% |
| 4 | 34.91 | 31.20 | 10.6% |
| 4.5 | 36.91 | 35.10 | 4.9% |
| 5 | 43.60 | 39.00 | 10.5% |
| 6 | 48.68 | 46.80 | 3.9% |
| 8 | 64.40 | 62.40 | 3.1% |
| 10 | 80.12 | 78.00 | 2.6% |
| 12.5 | 99.70 | 97.50 | 2.2% |
- Quality 304 (A2) and 316/316L (A4) are suitable for use on board.
Lead[edit]
- Density 11340 kg/m3
Timber[edit]
source 'Hout Vademecum'
- birch 660 kg/m3
- ocoume 420 kg/m3
- poplar 435 kg/m3
- teak 675 kg/m3
- MDF 750 kg/m3
Plywood[edit]
See Plywood.
