Difference between revisions of "Aventura 43"

Revision as of 16:50, 9 May 2011

General

• Lay out A is for the first boat, we have those drawings as a reference
• Lay out B is our boat (the second), it is a charter version with 8 berths
• Drawing Lay out B is a preliminary set up drawing only
• Not all space is used when it is inefficient or hard to reach for use
• Furniture is prefabricated outside the boat as much as possible
• Yard manager used to draw CNC building kits himself in 2D AutoCad
• Sheets are nested full, if possible move parts to another material in order to obtain this

Material

• Plywood birch 3050x1250mm
  • 15mm + 2x HPL 0.75mm draw 17mm
    • sole
    • furniture
    • seats
  • 4mm + 1x HPL 0.75mm draw 5mm
    • lining panels glued to steel construction
  • 4mm + 2x HPL 0.75mm draw 6mm
    • furniture backpanels

Colours

• Colour for Aventura 43 CHARTER is Abet 661 Collectie Legni - Pino Chambery (0.9mm conform website)
• When no colour than 2x white backing

Sole insulation

• 4mm rubber above enginer room only

Part codes

• 5 horizontal layers:
  • H1 sole
  • H2 intermediary
  • H3 seat
  • H4 intermediary
  • H5 ceiling

• 4 vertical segments:
  • V1 on top of H1
  • V2 on top of H2
  • V3 on top of H3
  • V4 on top of H4

• Compartments
  • AK aft cabin (achterkajuit)
  • VK fore cabin (voorkajuit)
  • SH wheelhouse (stuurhuis)

• Furniture
  • KN galley (keuken)
  • SF settee (sofa)

• Partnumbers
  • assigned clockwise

• Layer use in 2D Autocad
  • DS = section (doorsnede)
  • ST = steel (staal)
  • 2 = layout 2
  • FR = frame (spant)

• example: 2-BET-US-AK-WC-H1-01 = Layout 2, BETimmering-UitSlag-AchterKajuit-WC-Vloer H1, deel 01.

Ceilings

• 17mm base ply is mounted against all frames (see layer 1-BET-DS*)
• Aft deck is reinforced with 2 girders, here a '9mm birch plywood part is mounted first'?!?

Remarks Cabin 1 (forepeak)

Remarks Cabin 2

• 1 transverse bed 2000x800 direct on sole, see if you can use sole of layout A (VK-H1*)
• 1 longitudinal bed, max 1900 lenght? Forward engineroom bulkhead has large stiffeners, put first bulkhead in original position as layout A?

Remarks Bathroom 1

Remarks Salon / Galley

• settee as long as possible, foot end of berth cabin 2 under settee, if not possible than sofa as in layout A (part SF-H3-01)
• galley 'floats' partly above engine room hatches
• galley parts from layout A can be used again
• galley forward cabinet houses the distribution panel (W550xH750xD182) in the side, parallel to CL (see lay out A SH-K2)
• converter in layout A was in locker with distribution panel, now a new location must be found

Remarks Bathroom 2 (aft PS)

• longitudinal length to be reduced by 100mm

Remarks Bathroom 3 (aft SB)

• longitudinal length to be reduced by 100mm

== Remarks Cabin 3 (PS aft)

== Remarks Cabin 4 (SB aft)

==