Difference between revisions of "Spatio Navis 40"
From NavykI
(→50 Outfitting) |
|||
| Line 9: | Line 9: | ||
===Classification=== | ===Classification=== | ||
*CE-C | *CE-C | ||
| + | |||
| + | == 10 Design == | ||
| + | *windows | ||
| + | **sliding window in salon side | ||
| + | **supplier - cheapest(RAFA?) | ||
| + | **hull - glue plexiglass/lexan? | ||
| + | *portholes | ||
| + | **supplier - Gebo | ||
| + | **PS and SB can be non symmetrical | ||
| + | *deck hatches | ||
| + | **supplier - Gebo | ||
| + | **make sure you can reach the hatch for closing/opening | ||
| + | **entrance hatch - GRP Centerboard standard | ||
| + | *doors | ||
| + | **transom door - standard Gebo door? | ||
| + | *ventilation | ||
| + | **very important and permanent | ||
| + | **all spaces | ||
| + | *sidedeck steps - not IN bathrooms but well before them (possible use for breathers) | ||
| + | *transom stairs PS - last step ending under 45 degrees with CL | ||
| + | *transom gas locker SB - for 2x 5kg gas bottle | ||
| + | *swimplatform - length minimum 800mm | ||
| + | *swimplatform - lower part at least 200mm above DWL (to avoid slamming waves against swimplatform | ||
| + | *transom corners - well rounded | ||
| + | *shaping: | ||
| + | **no forming plates | ||
| + | **no bending plates | ||
| + | **only 'radiused' plates | ||
| + | *transom cheeks with knuckles? | ||
| + | *sidedecks - 450mm wide | ||
| + | *superstructure - max width 3100-3150 | ||
| + | *bench aftdeck - GRP | ||
== 20 Naval Architecture == | == 20 Naval Architecture == | ||
| Line 21: | Line 53: | ||
===Tanks=== | ===Tanks=== | ||
| − | * | + | *capacity: |
| − | ** | + | **500l FW (because of 2 showers) |
| − | |||
| − | |||
| − | |||
| − | |||
**500l fuel | **500l fuel | ||
| − | **500l FW | + | **500l WW (for example in keel, to not create heel/trim) |
| − | + | *tank status to not influence trim/heel | |
| + | *WW tank above FW tank, transverse in front of engine? | ||
| + | *all custom made PP tanks | ||
| + | |||
| + | == 40 Construction == | ||
| + | *as cheap as possible (simple, light) | ||
| + | *side stiffening - longitudinal T-stringers | ||
| + | *transverse bottom stiffening - CNC frames ending against T-stringers | ||
| + | *roof beams - CNC (profile is hard to make them all exact the same) | ||
| + | *sole on LG rectangular tubes 60x40 (check size), used for cables too (thrusters, windlass) | ||
== 50 Outfitting == | == 50 Outfitting == | ||
| Line 35: | Line 72: | ||
*fender around swimplatform (well rounded corners) | *fender around swimplatform (well rounded corners) | ||
*fender around transom cheeks (renters succeed to damage even this part of the boat with manouvring) | *fender around transom cheeks (renters succeed to damage even this part of the boat with manouvring) | ||
| − | * | + | *windlass with chainpipe through bow |
| − | + | ||
== 60 Systems == | == 60 Systems == | ||
| − | *exhaust - shell penetration in engine room, | + | *exhaust - shell penetration in engine room, via st.st. rectangular tube 100x60 to transom (check back pressure) |
| + | *heating | ||
| + | **Maritime booster | ||
| + | **cabins - radiators | ||
| + | **wet cabins - towel radiator | ||
| + | *hot water | ||
| + | **boiler on engine (WHY?!?!?! use a combi heater?!??!) | ||
| + | *toilet | ||
| + | **Jabsco Lite Flush? | ||
== 70 Interior == | == 70 Interior == | ||
*make several color proposals (renderings) based upon HPL (incl. non-wood) | *make several color proposals (renderings) based upon HPL (incl. non-wood) | ||
| − | + | *wet cabins | |
| + | **HPL, not spraypainted | ||
| + | **sole - cheaper Corian alternative | ||
| + | **prefab unit, including systems? | ||
| + | *salon - large flatscreen TV on lift | ||
| + | *sole - HPL teak and holly | ||
[[Category: Projects]] | [[Category: Projects]] | ||
Revision as of 13:48, 19 September 2012
Contents
General
- salesprice 170.000 € ex VAT
- to compete with:
- Jetten 37 AC
- Aventura 38 AC
- initial client - boat rental Schultz
Classification
- CE-C
10 Design
- windows
- sliding window in salon side
- supplier - cheapest(RAFA?)
- hull - glue plexiglass/lexan?
- portholes
- supplier - Gebo
- PS and SB can be non symmetrical
- deck hatches
- supplier - Gebo
- make sure you can reach the hatch for closing/opening
- entrance hatch - GRP Centerboard standard
- doors
- transom door - standard Gebo door?
- ventilation
- very important and permanent
- all spaces
- sidedeck steps - not IN bathrooms but well before them (possible use for breathers)
- transom stairs PS - last step ending under 45 degrees with CL
- transom gas locker SB - for 2x 5kg gas bottle
- swimplatform - length minimum 800mm
- swimplatform - lower part at least 200mm above DWL (to avoid slamming waves against swimplatform
- transom corners - well rounded
- shaping:
- no forming plates
- no bending plates
- only 'radiused' plates
- transom cheeks with knuckles?
- sidedecks - 450mm wide
- superstructure - max width 3100-3150
- bench aftdeck - GRP
Transom rounding
- well rounded to avoid damage during leaving quai side
- keep step of 150mm next to stairs so you can step on the quai side
Propulsion
- suggestion Schulz: Craftsman CM4.80 - price for 5 pcs €7700
- Schulz: Deutz engines are very reliable
Tanks
- capacity:
- 500l FW (because of 2 showers)
- 500l fuel
- 500l WW (for example in keel, to not create heel/trim)
- tank status to not influence trim/heel
- WW tank above FW tank, transverse in front of engine?
- all custom made PP tanks
40 Construction
- as cheap as possible (simple, light)
- side stiffening - longitudinal T-stringers
- transverse bottom stiffening - CNC frames ending against T-stringers
- roof beams - CNC (profile is hard to make them all exact the same)
- sole on LG rectangular tubes 60x40 (check size), used for cables too (thrusters, windlass)
50 Outfitting
- fender of rubber or rope
- fender around swimplatform (well rounded corners)
- fender around transom cheeks (renters succeed to damage even this part of the boat with manouvring)
- windlass with chainpipe through bow
60 Systems
- exhaust - shell penetration in engine room, via st.st. rectangular tube 100x60 to transom (check back pressure)
- heating
- Maritime booster
- cabins - radiators
- wet cabins - towel radiator
- hot water
- boiler on engine (WHY?!?!?! use a combi heater?!??!)
- toilet
- Jabsco Lite Flush?
70 Interior
- make several color proposals (renderings) based upon HPL (incl. non-wood)
- wet cabins
- HPL, not spraypainted
- sole - cheaper Corian alternative
- prefab unit, including systems?
- salon - large flatscreen TV on lift
- sole - HPL teak and holly
