Difference between revisions of "15038 Bestevaer 45 ST Pure"
From NavykI
(→Fore Cabin) |
(→Fore Cabin) |
||
| Line 78: | Line 78: | ||
===Fore Cabin=== | ===Fore Cabin=== | ||
| − | * | + | ====Navyk remarks==== |
| − | * | + | *bed > storage bottom is OC-18 |
| − | + | *lining > in way of sole it could be replaced by bracket boxes | |
| − | + | *batteries > additional bottom panel with battery cutouts could have cutouts for nylon straps to fasten the batteries | |
| − | |||
| − | * | ||
| − | |||
| − | |||
| − | |||
===Salon=== | ===Salon=== | ||
Revision as of 08:37, 21 July 2015
'Pure' is the name of new line of yachts, of which the first boat is named 'Nescio'. This first boat will be build for Eeuwe Kooi himself (owner/director KMY).
Contents
Planning
- Conform mail Willem Berends of July 16
- WK 30 Navyk to implement all comments and changes.
- WK 30 End of the week Navyk will send the draft files for review.
- WK 32 Bamboo wood will be delivered to KMY for surface preparations.
- WK 33 Until Wednesday Noon, KMY has the time to review and send some additional remarks.
- WK 34 All wood material (exl. floor) will be deliverer at CNC works.
- WK 34 End of this week Navyk will deliver the complete files to KMY.
- WK 35 CNC will cut all materials en deliver to the KMY.
TO DO
General
- access bolt connection for mounting superstructure
- drill holes and notches for assembly
- sole structure > create
- heating > add bulkhead penetrations for hose and grills
- labels > create excel sheet with codes for each part
- additional files:
- Marlan templates
- metal parts
- handrails > st.st. Ø28
- poles (structural) > aluminum > galley Ø60 / salon Ø80
- driver-drill
- total length including bit > 210mm
- distance shaft center to top of housing > 36mm
hatches and portlights
- Deckhatches:
- Lewmar Size 60 low profile: 39960030
- Lewmar Size 30 low profile: 39930030
- Portligths in superstructure:
- Lewmar Standard portlight Size 3: 393320200
- Portlights in cockpit:
- Lewmar Standard portlight Size 5: 393520200
hardware
- finish > stainless steel
sole
- base > 18mm ocoume, varnished all around
- finish > chest nut
- margin boards > width 70mm
- hatches > to be determined in combination with alu sole supporting structure
- hatch locking device > see material list
lining
- V-grooves, every 100mm, parallel to deckline/sheer
ceilings
- leather panels > mounted with Fastmount
entrance doors
- door width net standard > 560mm
- door width net minimum > 500mm
- gap under door > ?
- core > plywood ocoume 18mm
- cover panels > plywood bamboo 7mm
- hinges?
- mortise lock?
- handles?
- door plates/shields?
- height doorhandles?
- door catch?
- ajar hook?
lockers
- shelves > mounted with shelf supports (Hettich)
- FYI > solid corner profiles in furniture plintes will be painted white
- hinges > Hettich Intermat Soft....
- drawer runners > Hettich Quadro 30
- closing device > Kroon 372369
- shelf supports
seats
- seat cushion thickness 100mm
- back vertical
- seat panel 340mm above sole
berths
- matrass thickness 100mm
- bed slats 40 mm from Spacerflex
Fore Cabin
- bed > storage bottom is OC-18
- lining > in way of sole it could be replaced by bracket boxes
- batteries > additional bottom panel with battery cutouts could have cutouts for nylon straps to fasten the batteries
Salon
- pillar mast bulkhead > connected with FB 8mm, split mast bulkhead
- table
- chain plate reinforcement > mask
- lower hinge in forward upper cabinet will be solved by KMY
- counter top > raise 100mm
- add shelf profile between upper lockers
- box against FWD bhd > bottle storage, make narrower, add hatch in counter top (with fingerhole)
- upper lockers > move upper plinth outboard
Galley
- resize and reposition all drawer boxes conform final drawer runner
- pillar > cut hole in sole, large enough for welding
- fridge is a Webasto
- CR 85 EL - first choice
- CR 65 EL - second choice
- front to be white
- sink > Belship 0430331515CS
- stove > Force 10 F63356
- gimbal 30°
- faucet > Damixa Willow Kitchen Chrome
Remarks for yard
- fridge vent in plinth interferes with LED light
- fridge vent in cabinet side to be => 6500mm2 > apply Hafele grill?
- sole > large opening (no hatch) under galley counter
Bathroom
- material > panels can be normal HPL as rest of boat, the special quality W400-VV is canceled.
- entrance door > rotates outside and forward
- black water tank > behind toilet, 2 options:
- glass doors > model schematic and indicate operation
- sink > Belship 043018
- faucet > Hudson Reed Tec Crosshead
Aft cabins
- PS > bulkhead cutout, profiles, raise horizontal profile in line with sole deckhouse
- bed bottoms > hatches for access storage space under, support?
- lining > align knuckles with V-grooves
- entrance door > rotates inside
- technical space > add access hatches in longitudinal panels
- high locker > add plinth on top, moved outboard
Deck house
- 'pillar boxes' to be moved outboard 10mm
- 'pillar boxes' add recesses for technical panels, dimensions? KMY
- 'pillar boxes' pillar to model
- all panels to be white, except for bench fronts, 'pillar boxes' besides entrance and top of guest cabin SB
- bench fronts and top of guest cabin to be covered with 6mm bamboo as for entrance doors
- add solid profiles around top of guest cabin.
- WJ will provide correct model of entrance
- add solid profiles at vertical corners of transition salon/guest cabin to deck house
- stairs > add solid profile to vertical corner of lower step
- recess behind seats > about 50 wide, 100 deep
- lining besides entrance > add solid profile at vertical (skewed) corner
- benches > seat width 550mm
- benches > back inclinated
- benches > raise bottom to have 950mm between seat and ceiling, this 950 is including or excluding the cushion? KMY
- Aft cabin lining > reduce lost space behind lining
- Stair steps > use for storage (3 steps)
- Aft cabin top > removable plexiglass panel for light and air, detail? KMY
- PS bench > remove armrest, make suitable for transverse seating
- bed bottoms > raise 100mm for additional storage and wider matrass
- bed bottoms > hinged hatch
- bed PS > large drawer under
- handrail SB > to model
- handrail/pillar PS > to model
Modeling refereneces
Tolernace
- distance to frame flanges 20
Lining
- deckhouse > offset 62 from inside shell, lining will be glued against Hora windowframes conform P169 Detail windows.dwg (received June 30)
Base ceiling
- superstructure
- offset 58 from inside shell
- after rebuilding salon tolerance <7 (surface from aft bulkhead to fwd bulkhead)
- interference with stringers <2, to be solved on board
Sheet estimation
transverse grain
- 17mm single bamboo - 3 sheets - bench fronts SL / galley front / table sides
- 6mm single bamboo - 1 sheet - bench fronts DH
People
- Eeuwe Kooi - director/owner (not directly involved)
- Willem Berends - chain manger (responsible for contract)
- Willem-Jan van der Vegt - engineer (our contactperson)
- Haaie Andringa - foreman carpentry
Exchange work
- KMY negotiated €1.000 discount for delivering a 3D model of interior - send file is only a block file
- integration of heater ducting is not in contract
- info is not delivered on Monday, June 15 but came partially on June 16 and 17
As discussed
July 1, 2015
- furniture doors - 17mm is OK
- entrance hatch recess box - PUR insulated, put plywood panel in front
- stair steps solid wood
- cockpit sole - covered with cork 9mm
- lining - leather panels are canceled
- porthole boxes - yard makes tube, out of our delivery
June 16, 2015
- black water tank - to be determined by Navyk, volume around 50 liter, position SB behind toilet
June 11,2015
- tolerances
- vertical:
- sole to supporting structure - 0mm
- ceiling to structure - 0mm
- horizontal
- clearance from inner frame contour - 20mm (space between frames is reserved for systems)
- vertical:
- insulation type is PUR
- grain orientation will be vertical
- sole supports are alu tube 50x30x?
- cabinet interiors to be white
- KMY workshop facilities:
- no veneer press
- edge band machine for straight edges
- lamello machine
- round router bits R6, R8, R10, R12
- Navyk will route the ducting for airheating through the interior
- Navyk is free to use their own material naming
- Navyk will give a price offer for the aluminium sole supports
Structure model - modifications!
- Forepeak bulkhead - stiffeners will be on aft side (cabin side)
- Pilothouse - between the windows will be a vertical T-profile with a web of 50x6 and a flange of 50x8
- Entrance door forecabin - to be determined by Navyk, it will be a joinery door, not an aluminum door
- sole structure - to be determined, Navyk will make a price offer for this
