Difference between revisions of "Aventura 34 OC"
From NavykI
(→11023 - hull #3) |
(→To do) |
||
| Line 10: | Line 10: | ||
== To do == | == To do == | ||
| − | === 11002 | + | === 11002 BN 1 === |
*done | *done | ||
| − | === 11015 | + | === 11015 BN 2 === |
*done | *done | ||
| − | === 11023 | + | === 11023 BN 3 === |
| − | *bottomstringer foreship - make intercoastal | + | |
| − | *deck hatch | + | ==== Hull ==== |
| − | + | *swimplatform - extend deck aft 400mm, add second deck at an offset of 80mm down (net distance between decks 80mm) | |
| − | * | + | *bottomstringer foreship - make intercoastal ''DONE (VC)'' |
| + | *ropefender - make strips 50mm wide over nose, from F17 forward, 1 strip at knuckle hull/bulwark, 1 strip at offset 80mm down | ||
| + | |||
| + | ==== Deck ==== | ||
| + | *gaslocker - move from sidedeck to PS cockpitbench, directly aft of superstructure bulkhead, no hatch detailing (yard will make alu hatch) | ||
| + | *cockpit benches - add 2 short hatches in benches against transom, height as hatches in side benches | ||
| + | |||
| + | ==== Superstructure ==== | ||
| + | *superstructure aft bulkhead - move aft 150mm (modify windows?), remove vertical 'roof extension' aft of windows, we can decide if roof extension over cockpit will remain or not | ||
| + | *deck hatch forepeak - make cutout in roof 4mm bigger to accommodate vertical FB 30x4 (hatch base about 10-15mm above roof) ''DONE (VC)'' '''BUT''' it must be changed again: deckhatch will be mounted on top of L50x50x5 profiles with flanges pointing inward | ||
| + | *deck hatch salon - mark HIP for sliding hatch Webasto serie 60 (HIP should be about 1100x1800) | ||
| + | |||
| + | ==== Miscelaneous ==== | ||
| + | *engine - move aft | ||
*nest - add remark for cutter - 'platen op holle zijde markeren' | *nest - add remark for cutter - 'platen op holle zijde markeren' | ||
[[Category: Projects]] | [[Category: Projects]] | ||
Revision as of 13:42, 27 October 2011
Contents
General
Contacts
- sales - Aventura Yachts contactperson Bert Meijer
- construction - Bronsveen contactperson Jan Aslander
- construction (subcontractor Bronsveen) - CMS schepen contactperson is Delmer Los
- interior / paintwork - Jurjen Mulder Jacht- en Scheepsbetimmering contactperson Jurjen Mulder
- initial client - boat rental Schultz
Questions
To do
11002 BN 1
- done
11015 BN 2
- done
11023 BN 3
Hull
- swimplatform - extend deck aft 400mm, add second deck at an offset of 80mm down (net distance between decks 80mm)
- bottomstringer foreship - make intercoastal DONE (VC)
- ropefender - make strips 50mm wide over nose, from F17 forward, 1 strip at knuckle hull/bulwark, 1 strip at offset 80mm down
Deck
- gaslocker - move from sidedeck to PS cockpitbench, directly aft of superstructure bulkhead, no hatch detailing (yard will make alu hatch)
- cockpit benches - add 2 short hatches in benches against transom, height as hatches in side benches
Superstructure
- superstructure aft bulkhead - move aft 150mm (modify windows?), remove vertical 'roof extension' aft of windows, we can decide if roof extension over cockpit will remain or not
- deck hatch forepeak - make cutout in roof 4mm bigger to accommodate vertical FB 30x4 (hatch base about 10-15mm above roof) DONE (VC) BUT it must be changed again: deckhatch will be mounted on top of L50x50x5 profiles with flanges pointing inward
- deck hatch salon - mark HIP for sliding hatch Webasto serie 60 (HIP should be about 1100x1800)
Miscelaneous
- engine - move aft
- nest - add remark for cutter - 'platen op holle zijde markeren'
