13012 Dykstra 62

General

Contacts

• client: Dick Alewijnse (NL) - DA is contactperson for all questions regarding systems
• project manager: Robin ten Hoope (NL) - RtH also drew up the interior since GDNP did not have time for it
• contact person GDNP: Erik Wassen (NL)

Trivia

• carbon mast costs about 250K which is more expensive than the interior (and the interior is more expensive than the aluminum construction)
• sistership 'Windhunter III' is build by Aluboot (Henk Borneman) and owned by Johan Mast
• ballast system with dumphatches is developed by Heine Deelstra from Gaastmeer Design, in cooperation with K&M Yachtbuilders

40 Construction

• frames will be all plate
• bulb profiles change into FB

Liftkeel

• detailing might be done by Frans Brandjes

60 Systems

• fuel

* Must be added the rest of the DN's * Filling and vent pipe is Alu, transfer and consumers st. st. * Content table from paper space to be completed

• bilge

* Piping is PP in combination with hose (the crossover pipe between wing tanks is alu) * Add the rest of the diameters for piping * Put in the system drawing and rihno smell traps where neded (freezer, AC drip trays, laundry machine, dishwash), for sinks will be a siphon with smell trap. No smell from the collection tank should go out.

• black water

* Must be added the rest of the DN's * Content table from paper space to be completed

• exhaust

* the water separators positioned on the transom to avoid mounting a goosneck * Content table from paper space to be completed * The engine waterlock can be replaced with - Halyard side 45 dgr in/ top out H001459 Foot 275x275, if the one from the diagram does not comply with the producer's mounting requests. * The generator waterlock and separator must be dimensioned (how many liters) * The generator waterlock can bilgebe Halyard if the one mentioned in the diagram does not comply with the producer's mounting requests.

• seawater

* Add diameters for piping * Add seawater intake for chiller plant Webasto. Can be from the manifold or must be separate? * Engine cooling- indirect?

General

• overboards - all above WL
• overboards - combine as much as possible
• valves - reduce number of valves where possible
• drafting
  • uniform use of symbols
  • uniform size of symbols
  • all tables grouped vertical in right side of drawing
  • all on A2 format?
  • use new titleblock / notes / table
• collect supplier data for each appliance (in the project folder there is not any documentation)

Ballastsystem Windhunter

• • breather pipe must have sufficient diameter, Windhunter has Ø50 which is considered too small, they advice Ø80
  • breatherpipes go to grills in aftside doghouse
  • when breatherpipes overflow you know the tanks are full
  • Goiot hatches operation lines are lead to the cockpit and have a 2:1 tackle
  • Goiot hatcehs have a lever
  • double bottom is used as cross over, K&M is not satisfied with (hard to make watertight, no inspection possible) and prefers 2 or 3 large diameter pipes
  • Goiot deckhatch rectangular, for example 300x500 or 250x400, plexiglas replaced by aluminum panel
  • advantage of using standard deckhatch is that spareparts like gaskets can be easily found and replaced
  • Windhunter uses only ballastwater, we use a combination with grey water which gives smells so the breather pipe should be a closed ring?

Bilge

• manifold in galley (against trunk ER?), all manual valves well accessible

Fresh water

• reduce number of valves
• toilets possibly come with double connections for FW / seawater, then no valve required, check this out (possible supplier is Raritan or Tecma)
• pumps, hydrofor, etc - to be removable: valves fore and aft
• add taps at low points
• reduce overboards by combining pipes

Sea water

• galley - own faucet, no connection to FW faucet

Black water

• breather aft in transom, forward in mast?

Fuel

• pump does not require electric valves fore and aft

Electric

• generator - Northern Lights? Wisperpower company is running into troubles?

Propulsion

• Steyr 4 or 6 cylinder
• check out if 26" prop can be combined with Twindisc gearbox, because of space issue, ER trunk might require modification, together with interior engine/shaft angles can be modified, keep 30% tipdistance for propellor, longitudinal position can be modified
• propellor
  • Flexofold 26" (optional 25" or 28", pending on engine and gearbox combination, issue is behaviour of sailing reverse)
• drawing of Twindisc is in e-mail of 22-07-2013