Spatio Navis 40

BN04

• linesplan - to avoid ballast add volume in aftship (improves shower aftcabin) or decrease in foreship (improves air draft)
• windscreen - move wiper engines up to increase clearance with deck (ask Jan how much)
• see mail Jan (Customers/Centreboard/Spatio Navis 40 B04)

BN02

• Rope fender detail.DONE
• Rectangular pillar support. DONE
• Cutout in diesel tank for: engine tour and retour, heater intake and breather. Crossover pipe moved more aft because of BHD stringers. DONE
• Added closing plate for ventilation in aft toilets in wings. DONE
• New cutouts through shell for toilet and engine strainer.
• Supports for hot water and heating pipes and cutouts.
• Cutout for fresh water from tank in frames.
• Railing plate added after fillet radius changed conform CC40 railing plan.
• F5 cut, new LG SKLG.
• F14+150PS from deck moved at F14.
• Cutout for heating exhaust moved 65mm fwd because for boiler support.
• Bracket incorporated in rudder support for angle indicator.
• Handrail in transom move on wall, for this the 230V HIP must move down? (now the handrail is on bench).
• Support for toilet pump in ER.
• Stringers for rope fender cut in aft part according to st. st. detail.
• Make 1 HIP for ME gooseneck.
• HIP in steering support for rudder stopper round bar diameter 30mm.
• Added 5mm rope fender tensioner bkt.
• Saloon ventilation via console cancelled.
• Add 3D views is transverse construction for next boat.
• Move side stringers near portholes move 50mm down.
• Make deck frames in fore peak 50 like in aft.

FEEDBACK

interior

• bulkhead panel at dinette mirrorwise in nest

BN01

FEEDBACK

• after launching 10 August 2013 Berlin
• after sailing 2 days end of October 2013 Berlin

naval architecture

• hydrostatics
  • floats around (modified) waterline but trimmed aft, about 2.5 degrees
• stability
  • great initial stability (a person on the side deck hardly effects heeling)
  • heeling with persons on sidedeck:
    • 80kg 1.3°
    • 177kg 2.5°
    • 260kg 3.2°
    • 337kg 4.0°
    • 418kg 5.1°
    • 485kg 5.8°
    • 564kg 6.4°
    • 657kg 7.4°
    • 757kg 8.6°
    • 869kg 9.6°
• sailing characteristics
  • good directional stability
  • good sailing characteristics
  • powerful bowthruster, very confenient
  • reverse
    • boat starts 'spinning'
    • manouvres very easy with rudder in neutral position and steering with bow thruster
  • speed
    • easily achieves hull speed
    • @2200 14.8 knots (or km/h?) and no trim
    • topspeed is ? (Jan?)
    • topspeed generates only small waves
  • at full speed the swimplatform just remains dry
  • motor is overdimensioned (request of owner)
  • engine noiselevels
    • outside little noisy (comes via morse cable?)
    • inside you hardly hear the engine

trim measurements (by Jan)

• conditions:
  • FW tank full (300 liter)
  • Fuel tank full (500 liter)
• measurement with 80kg on foredeck
  • distance WL to lower fenderstrip at bow is 1460mm
• measurements without Jan
  • distance WL to lower fenderstrip in way of freeing port (about midship) is 950mm
  • distance WL to knuckle at transom is 70mm
• measurement with 265kg on foredeck
  • bow lowers 40mm

missing items in weight estimation

• Todd bench aftdeck - 20kg
• cabrio hood - 50kg
• ceilings
• Corian surfaces and bowls

interior

• forecabin - entrance door interferes with bathroom doors - 2nd boat the entrance door will open aftward
• lack of storage drawers (for example for shoes)
• showerwater does not drain (yard problem)
• missing curtain (yard)
• electric switches - are hit when you pass by (yard)
• galley - no towel hooks
• forecabin - more cloth hooks

outfitting

• fenderlines cannot be tied to anything - 2nd and 3rd boat will have sleeves cut under tube in railing screen
• entrance hatch - cannot be locked (yard)

General

• salesprice BN01 205.000 € ex VAT (Schulz)
• salesprice BN02 215.000 € ex VAT (Schulz)
• salesprice BN03 230/240.000 € ex VAT (Schulz?)
• to compete with:
  • Jetten 37 AC
  • Aventura 38 AC
• initial client - boat rental Schulz, 2 brothers; Thomas and Steffen, renting a lot to group of man (biliart clubs, etc.)

Classification

• CE-C

Yard budget

• estimated (mail 01-Jun-12):
  • steel 700
  • wood 750
  • paint 750
  • systems 350
  • sandblasting 100
  • outfitting and delivery 150

Supplier discounts

• 20% Marine Booster
• 40% Stazo
• 25% Webasto

Drawing list

• Note:
  • Below list is not complete
  • Drawings can be combined if suitable
• CE?

10 Design and styling

• 10-100 general arrangement
• 10-910 general data
  • net weight construction
  • net weight interior
  • total weight
  • COG
• 3D presentation models?
• renderings?

20 Naval Architecture

• 20-100 linesplan
• 20-300 centralizer

40 Construction

• 40-100 longitudinal construction plan
  • tank arrangement
  • propulsion arrangement
  • rudder arrangement
  • fender details
  • portholes and hatches
  • windows
  • bench aftdeck
  • ventilation
• 40-110 transverse construction plan (SC)
• 40-130 shell penetrations
• 40-200 expansions hull (SC)
• 40-210 expansions superstructure (SC)
• 40-220 bending and forming
• 40-300 build moulds
• 40-400 plate nests steel
• 40-410 plate nests stainless steel
• 40-800 FW tank
• 40-810 WW tank
• 40-820 Battery box+
• 40-830 Chain locker
• 40-910 material estimation steel
• 40-920 key data
  • net weight
  • brut weight
  • loss %
  • COG
  • cutting length

50 Outfitting

• 50-110 companion way
• 50-115 windows
• 50-120 windscreen
• 50-160 stainless steel (incl. material estimation or on separate document?)
  • railing
  • table aft deck
  • bow protection plate
  • hand rails
  • mast
• 50-170 steering arrangement
• 50-180 chain box
• 50-210 sprayhood and bimini
• 50-220 dashboard panel

60 Systems

• 60-100 bilge drainage
• 60-110 exhaust gas
• 60-120 ME cooling
• 60-130 fuel system
• 60-140 fresh water system
• 60-150 waste water system
• 60-160 heating
• 60-170 electric

70 Interior

• 70-100 set up interior
• 70-105 general detail plan
• 70-110 sole plan
• 70-120 lining plan
• 70-121 base wood plan
• 70-130 ceiling plan
• 70-140 lighting plan
• 70-150 profile list
• 70-160 cabin doors
• 70-161 salon table
• 70-162 cabin stairs
• 70-163 cooling box
• 70-170 upholstery
• 70-800 nests
• 70-810 furniture expansions
• 70-820 furniture assemblies
• 70-910 key data
  • net weight
  • brut weight
  • loss %
  • COG
  • cutting length
• 70-920 material estimation plywood
• 70-930 hardware list
• 70-940 hardware catalogue
• 70-950 assembly names

10 Design

• sales strategy is to offer as much berths as possible for the lowest price so the boat will be very interesting for the rental market
• only developable surfaces:
  • no forming plates
  • no bending plates
  • only 'radiused' plates
• simple and cheap - the less components the cheaper to build
• furniture to be split in units which can be prefabricated outside the boat (and outside the premises)
• sidedeck steps - not IN bathrooms but well before them (possible use for breathers)
• transom stairs
  • width 500-550 (older people)
• last step ending under 45 degrees with CL
  • transom gas locker PS - for 2x 5kg gas bottle
• swimplatform
  • length minimum 800mm
  • swimplatform - lower part at least 200mm above DWL (to avoid slamming waves against swimplatform
• transom corners - well rounded
• transom cheeks with knuckles?
• sidedecks - 450mm wide
• superstructure - max width 3100-3150
• bench aftdeck - initially steel, later GRP?
• railing cloths - steel (Schulz)
• rope fender around hull
• rubber fender around swimplatform
• steering
  • wheel Ø800
  • wheel nearly horizontal

50 outfitting

• windows
  • sliding window in salon side
  • supplier - Rhigo (mail 03-11-2012)
• portholes
  • supplier - Gebo
  • PS and SB can be non symmetrical
  • hull - glue plexiglass/lexan?
  • hull - combine with ER air intake?
• deck hatches
  • supplier - Gebo
  • make sure you can reach the hatch for closing/opening
  • entrance hatch - GRP Centerboard standard
• doors
  • transom door - Gebo hatch 900x600
• gas locker
  • door Belship
• ventilation
  • very important and permanent
  • all spaces
• aftdeck
  • fridge
  • sink + tap
  • helmsman seat - Swingback Seat with Stainless Steel Arms Todd USA (fridge integrated?) (mail 16-10-2012)

70 interior

• aftcabin
  • bed under 45 degrees against transom
  • option for double cabin layout (can be non symmetric)
  • double bed convertible into 2 single beds (sliding/hinging system, seen on Greenline 33)
• headroom
  • bathrooms 1900

20 Naval Architecture

transom rounding

• well rounded to avoid damage during leaving quai side
• keep step of 150mm next to stairs so you can step on the quai side
• hull transom can stop before rounding (shortening hull)

tanks

• capacity (Ontwerp instructies SP-N40):
  • 500l FW (because of 2 showers)
  • 300l fuel
  • 500l WW (for example in keel, to not create heel/trim)
• tank status to not influence trim/heel
• all custom made PP tanks
• fuel - if only 1 tank forward of engine than steel tank against bhd, not attached to shell, condens sump with baffle plate above and tap

30 Propulsion

• engine - IVECO N45 MNA M10.2 74 KW 100PK (mail 15-10-12)
  • adjustabel mounting with spacers (as CC40?) (mail 19-11-12)
• gearbox - Technodrive TM93 (mail 15-10-12) ratio 2.09:1 (phone 10-12-12)
• coupling/thrusterbearing
  • Aquadrive (Ontwerp instructies SP-N40)
  • angles of Aquadrive in and out to be equal
• shaft Ø40 ITAL cone 1:10
• propellor - 'standard'
• nozzle - canceled (by phone 5-11-2012) alternative prop protection with 2 horizontal fins welded to the keel/skeg, length is half prop Ø
• bow and stern thruster - Sidepower 100kgm 12V in tube Ø185 (confirmed 6-11-12 by mail)
• suggestion Schulz: Craftsman CM4.80 - price for 5 pcs €7700
• Schulz: Deutz 1013M engines are very reliable
• Schulz: replacing 10 propellors per year, sometimes including shaft, because of under water rocks/stones
• rudder
  • plastic 50mm
  • sheet size 2000x1000 - consider when designing rudder (width <=500 for example)
• shaft lubrication - with hose connected to exhaust breather (see pictures Aventura 43)

40 Construction

• as cheap as possible (simple, light)
• yard budget 600 manhours
• side stiffening - longitudinal FB CNC
• transverse bottom stiffening - CNC frames ending against stringer
• roof beams - CNC (profile is hard to make them all exact the same)
• round corners of pipe segment - choose 1 radius for all corners
• NOTE: developable expansions with overlength 150 (distance between rolls of Jan his machine)
• sole
  • longitudinal rectangular tubes 60x40x3(as Aventura 43), used for cables too (thrusters, windlass)
  • partially removable for entering/rotating the sanitary units
• salon will be 'removable' in order to bring in the prefabbed interior parts, coupling detail as CC40, see notes inbox\'Ontwerp instructies SP-N40.doc'
• sandblasting - make sure all spaces are accessible for sand blasting
• moulds - boat is build upside down (including lower part of superstructure), deliver moulds with first boat
• rudder cylinder foundation - consider VDO rudder sensor
• incorporate:
  • ears/lips for interior positioning
  • ears/rings/holes for piping
  • system foundations
• steering position
  • instruments removed from IVECO panel
  • Trespa panel (ga ik gebruiken want ik heb hier nogal wat liggen.)
  • window wiper panel
  • VDO FO gauge
  • VDO FW gauge
  • WW gauge
  • Ray Marine Tridata or Bidata
  • VDO rudder angle indicator
  • Side-Power panel
  • panel with 6 rocker switches for:
    • horn
    • de activate buzzer
    • instrument lighting + navigation lights
    • anchor light
    • bilgepump
    • bench lighting aftdeck (optional)
  • engine control (side mounted)
  • may be - radio control
• bulwark pipe 1" thick walled (33.4x3.25)
• swimplatform
  • open construction
  • draining aft (1.5° at CL)

Paneel ook zo opbouwen met lange lasbochten (5S?) en achter een 10mm RVS rond. In het frame plaat met gat –randen 30 mm- waarbij Trespa plaat bovenzijde op hart buis ligt.

Penetrations

• standpipes:
  • steel
  • length 50mm + thread

hull

below DWL

• 1x cooling water ME
• 1x black water over board (1.1/2" conform Jan)
• 2x inlet toilet (1" conform Jan in mail 8-12-12)
• 2x transducers of bi data (HIP Ø52 see mail Rimare 12-12-12) (2 holes confirmed by phone by Ronald from Rimare on 20-12-2012 ('it concerns a Seatalk 1 generation instrument'))
• 1x rudder shaft (HIP Ø61)

at DWL +50

• 1x galley (1.1/2" conform Jan)
• 1x bilge (1.1/2" conform Jan in mail 8-12-12)
• 1x grey water
• 2x side deck drains

other

• exhaust at DWL +100
• exhaust heater?
• chain box - inox pipe 1/2", penetration and cut under an angle so a scoop will appear (hose ID21 white)
• shore connection at transom (HIP Ø56, DG Rubber)
• shore connection in transom SB, as high as possible
• topsides, under ropefender at same distance:
  • deck drains
  • FW breather
  • WW breather
• ER air intake
• portholes
• steering console: engine control

deck

• windlass - chain through deck with pipe st.st.Ø88.9
• ventilation through aftdeck - st.st. 2.1/2" (76)
• side deck drains st.st.
• fill FO
• fill FW
• suction WW

superstructure

• forecabin - cable penetration mast st.st.Ø35x2 (40 above deck, 10 below deck)
• window wipers - 3x socket
• breather FO
• portholes
• windows
• deckhatches
• companionway

tanks

• breather - pipe OD25 (mail 8-12-12)
• filling - pipe 1.1/2" (mail 8-12-12)
• cross over - pipe 1.1/2" with male thread and 2x valve
• retour - socket for 1/4" copper pipe
• supply - socket welded in top, suction pipe in tank

50 Outfitting

ER sole

• aluminum 5mm
• width max. 600
• covered with anti slip foil (see paint and insulation)

ventilation

• forecabin - 2 mushrooms on cabin
• wet cabins fore - 2 mushrooms on cabin with Vetus ventilator
• salon/galley - 2x dorade
• wet cabins aft
  • pipe Ø76 st.st. through deck with Vetus ventilator (40mm under deck)
  • flexible hose Ø76 (black or white) connects st.st. deck penetrations to Vetus ventilators (mail 8-12-12)
• aft cabin - 2x pipe Ø76 in bench?
• steering console ventilation to salon or aft cabin?

steering

• Levanto 38 has comparable displacement and steers well so we will try to use the same system BUT we have to use components of CUNO if possible:
  • arm yard made
  • cylinder Ultraflex UC215-I (111kgm)- LC465 40-52, 115kgm from CUNO
  • pump Ultraflex UP39 - LS451140, 40cc, with check valve and mounting bracket included from CUNO
  • wheel Ø575 (conform dwg)- Model for this project Ø550 Stazo type 12
  • arm strikes are tube 60x30
  • cylinder stroke should be slightly bigger then strike

fenders

• lower fender of rubber around swimplatform (well rounded corners) - starting at aft ER bulkhead, modified Aventura 43 profile, shore 90 (ask for new drawing)
  • min. bending radius R=500mm (mail 23-11-2012)
• rope fender
  • Ø110 (mail 22-11-2012)
  • around hull and transom cheeks (renters succeed to damage even this part of the boat with manouvring)
  • turnbuckles: M12, max. length 350mm

windlass arrangement

• manual Cuno - Lofrans Royal
• chainpipe 76x2mm RVS 304 through bow
• anchor - 35kg st.st. polished - TBS?

navigation lights

• no LED
• boardlights - mounting by yard (see pictures Vacance 1300)
• anchorlight
• steamlight
• sternlight

stainless steel

• 4x double bollards - for dimensions see PDF
• 2x single bollard on swimplatform (smaller model), directly welded on swimplatform
• flagpole support at bow and transom
• anchor protection plate at bow
• fender fairings
• handrail rooftop
• handrail transom (horizontal)
• railing
  • 700mm above deck (mail 07-01-2013)
  • pipe 30x2 and 25x2 (metric)
• mast
  • folding
  • TV antenna dome
• swimladder (see drawing inbox)
• boarding ladder side with 2/3 steps (see pictures)
• nav lights
  • NO Lopo lights (mail 29-11-2012)
  • board lights - supports on lower coachroof
  • sternlight - integrate in bench?
  • anchorlight - find solution

aftdeck

• sink
• cooling box in helm seat
• table - for mounting see detail dwg in inbox
• bench
  • steel
  • no bottom
  • no draining of interior
  • plastic hatches (as gaslocker) - size to allow storage of cylindrical fender 200x650 (Cuno)

hatches and portlights

• make Gebo
• portlights fixed in cabins
• portlights opening in bathrooms
• deck hatches 500x500
• transom hatch 900x600
• companionway without window

sliding hatch

• GRP
• recessed
• dimensions as 476
• NOTE: 18-12-12 Jan accepted a proposal with Lexan sliding hatch

windows

• supplier: Gebo, type Light Line (mail 22-11-12)
• indicate wall thickness on drawing (steel + PVC)

windscreen

• see remarks 'Ontwerp instructies SP-N40'
• window wiper 3x, see mail 30-11-2012

60 Systems

general

• all overboards - with valve
• through hull - pipe steel lenght 50mm plus thread

fuel

• all copper Ø8 (ME supply, ME return, heater)
• ME: 1/4" connection to tank/manifold - 1/4" valve - compression fitting - copper tube - compression fitting - reinforced fuel hose - engine
• NO no smell filter
• breather pipe Ø25x2 st.st. in lower side of superstructure 'cheek' (not wing)

bilge

• pump - Cuno 50880-1000
• switch - Belship 032351
  • switch will activate only a buzzer at steering console
• limber holes in all frames for water to drane in to the bilge sump
• sump strainer Whale (supplier Belship)

exhaust

• one side
• hose minimum bending R200, confirmed by Jan
• st.st. tube Ø100mm above DWL (check with CE)
• waterlock Ø100mm Cuno (as Aventura 43)
• breather (see pictures Aventura 43)
  • brass fitting with connection for shaft lubrication
  • breather line copper Ø8 connected to top of exhaust loop with socket st.st. 1/4"
  • hose 51?
  • transparant hose to see water level

cooling ME

• short stand-pipe of about 50mm (so pipe interior can be painted with brush)

heating

• 5x 2kW heat exchanger with st.st. grill:
  • 1x forecabin
  • 1x aftcabin
  • 1x dinette/double cabin
  • 2x salon
• wet cabins - towel radiator
• piping - Ø20mm - iFIT by Georg Fischer (full CAD library available on website) (for parts see mail 12-11-12)
  • when Webasto tap unit is used a short pipe of Ø25 iFIT is requiered

Webasto 90ST

• Thermo 90S 12V Plug & heat - Webasto 77054700 - € 1.886,40 (2011-03) (project 476)
• thermostat for 90ST / 24V -Webasto 25011C - € 39,88 (2011-03)
• expansiontank with sideglass and dop - Webasto 79289500 - € 215,82 (2011-03)
• exhaust thermo isolatie L=1850mm - Webasto 1313978A - € 63.00 (2011-03)
• exhaust silencer 38mm RVS met steun - Webasto .14 - € 116.42 (2011-03)
• exhaust clamp 42mm (9002255A) - Webasto 79643700 - € 5,63
• NOTE: Webasto writes in their mail of 18-10-12 (our mail 12-11-12) that the radiators are not enough for the heater to dispense it's heat so they offer a blower of Isotherm, initially 1 but more might be required

Webasto DBW 2010

• DBW 2010 12V CH - air heating - € 2.973,76 (2012-10 see offer in inbox)

Webasto DBW 2016

• DBW 2016C 24V TAP, incl. 3391438A 20 ltr. buffertank isotemp - Webasto 3391826A - € 2,721.60 (2011-03)
• expansion tank 8l 'Aquabox' - Webasto 149036 - € 44.85 (2011-03)
• bracket for expansion tank - Webasto 3200627A - € 19.51 (2011-03)

ventilation

• wet cabins - mushroom Vetus
• Vetus Typhoon in bench aftdeck for permanent ventilation (Ontwerp instructies SP-N40)
• Vetus Tom as on 483 (Ontwerp instructies SP-N40)

ventilation ER

• ER - as Aventura 43 (Ontwerp instructies SP-N40)
• NO blower (mail 7-11-2012)
• grill as Aventura 43 (mail 7-11-2012)
• ventilation hose Ø178 connected to MOFI100 and in ER side deck HIP Ø180 (hose is Ø170-190 and will be screwed down into steel through ribble)
• ventilation hose short on one side, long on other side

fresh water

• accumulator tank 8l (Cuno 337020)
• bracket set (Cuno 337021)
• pump Jabsco Max 4 (Cuno 3368) / Jabsco VSD Sensor Max 14
  • bracket set has provisions for mounting the pump so no separate pump foundation required!
• boiler 40 lt Cuno 230V + engine connected (as Aventura 43)
• sink on aftdeck
• piping - Ø16mm - iFIT by Georg Fischer (full CAD library available on website)
• toilets flush with sea water
• breather nipple in topside under rope fender

waste water

• galley drains directly overboard
• no smell filter Belship (Whale) as 483

black water

• issue - when tank is full the shit exits via breather or makes a pipe burst which drains the shit into the boat - how to avoid?
  • SH: when tanks is full the indicator should give a signal which stops the operation of the toilet flush button, together with an indicator (blinking light) on the flush panel
  • Sealand toilets come with above system
  • additionally a tank overflow will be installed which drains directly overboard
• tank material - plastic
• tank connections
  • toilet drains
  • deck suction
  • overflow
  • overboard (with Jabsco macerator pump type 18590 (Cuno 18590-2092)- will be mounted directly on tank with threaded 1 1/2 connection, so no separate foundation required!)
  • note: socket + elbow for pump line to be high enough for enabling screwing in of the pump
  • overflow + overboard connected on 1 through hull fitting + valve (under waterline)
  • all connections 2"
• all piping - Ø50mm - PVC-C by Georg Fischer (full CAD library available on website)
• breather in topside under rope fender

grey water

• 1x grey waste tank 16 lt Whale (in foreship, from aftship will come via pipe into this box) with the following connections:
  • showers
  • wash basins
• grey waste tank will drain directly overboard
• wash basins - hose 38, optional with PVC-C 50

steering

• wheel Stazo (mail 24-12-2012)

electrical

• panels 12V / 230V as Aventura 43
• 12V panel in aft cabin CL
• 230V panel in furniture salon SB
• second alternator on engine 12V / 150A
• NO optional generator (mail 01-11-2012)
• engine - comes with a relay box which must be mounted nearby
• switches - Cuno
• R25 at deck frame ends for cable penetration
• wiper engine cables:
  • 12V socket mounted next to engine (HIP!)
  • all wiper engines directing in same directin so sockets are non-symmetrical (PS/SB)
  • cables through frames to steering console
• cables from forecabin top are routed down inside double wall SB shower
  • nav lights
  • coax TV antenna
  • horn
• cable loom steering console about Ø80mm
  • 2x engine control
  • 2x hydraulic hose/pipe
  • 12V cables

batteries

• 2x foreship for thruster
• 2x aftship for thruster

instruments + navigation

• Raymarine Bi-data
• navigation lights - no LED

ligthing

• LED in salon, other spaces normal lamps (but interchangable with LED (Ontwerp instructies SP-N40)
• switch - wall mounted (mail 02-Oct-12)

70 Interior

materials

LATEST - 19.02.2013

• Bulwark and walls - 15mm plywood + 2x Oak veneer = draw 17mm thick / 04mm plywood + 1x Oak veneer = draw 05mm thick / 09mm plywood + 2x Oak veneer = draw 11mm thick
• Furniture walls - 17mm plywood painted = draw 17mm thick / 04mm plywood painted = draw 05mm thick
• Furniture interior - 15mm plywood + 2x HPL White = draw 17mm thick
• Furniture corners - Oak solid wood profile
• Furniture moldings - Oak solid wood profile
• Lining - 11mm plywood painted = draw 11mm thick
• Deckhouse - 10mm PVC white
• Ceiling - something from WHITZAND - we don't make Nesting for it
• Ceiling borders (curtains) - Oak solid wood profile
• Cabin doors - preferred 30 mm PVC painted
• Toilet and shower - 15 mm plywood +2x HPL White = draw 17mm thick
• Head sole, galley top toilets top - Corian 12.3mm +2.7 mm glue = draw 15mm thick
• Salon sole - Baryfloor 6-6-6 (total 18mm)+ 2x HPL = draw 20mm
• Other cabins sole - 18mm birch + 2x HPL = draw 20mm

HISTORY

• HPL (mail 03-10-2012, includes price offer)
• tops - latest idea jan: Wilsonart 13mm (mail 11-28) - Wilsonart
• sole
  • salon Baryfloor 6-6-6 (20kg/m2)
  • salon finish HPL teak and holly (1st) or PVC (2nd)
• make several color proposals (renderings) based upon HPL (incl. non-wood)
• hinges and closing devices as 483
• superstructure sides iwo windows: PVC 10mm

• Solid wood for corners and molds
• Polyrey HPL (min. bend radius 300 mm)
• 2x 07mm plywood + HPL for curved surfaces (e.g. bed in aft cabin)
• 15mm base + 2x HPL for walls = 17mm (mail 06.12.2012)
• salon sole - baryfloor 6-6-6 (total 18mm)+ 2x HPL = 20mm
• other cabins sole - 18mm birch + 2x HPL = 20mm

sole

• hatches where required for removing debris in bilge
• hatches for access any hose clamp

basewood

• deckhatches - include panel for mosquito screen (see mail 15-12-12)

upholstery

• possible supplier is Gisa Tex (D)

wet cabins

• spraypainted
• sole - Wilsonart
• prefab unit, including systems?
• toilet - seat height maximum 490mm (mail (26-11-2012)
• cabin PS fore
  • try to create 600mm distance between wall and vanity (mail 01-12-2012)

salon

• stairs - mounting as table aft deck (reinforcement in sole required?)
• removable panel in aft wall for access instrument panel of steering console

appliances

• NO hood above stove
• toilet - SeaLand MasterFlush Electric by Waeco
• wash basins - Alape glassed steel
• TV lift - 230V see purchase list ?!? (Ontwerp instructies SP-N40)
• optional
  • microwave (under sidedeck?)
• toilets 2x Sealand 8600 series, short model
• Wilson art sinks see down load section.

light plan

• ceiling spot - under mast for access cables

80 Paint and insulation

• insulation
  • hull - 40mm spray PU or rockwool
  • decks / superstructure - spray PU? (was Kingspan Thermaroof TR26)
  • ER - RG36 1000x1000x60
• antifouling - up to DWL +100