15038 Bestevaer 45 ST Pure

'Pure' is the name of new line of yachts, of which the first boat is named 'Nescio'. This first boat will be build for Eeuwe Kooi himself (owner/director KMY).

TO DO

General

• hatch coamings + Sky screens (Ocean air)
• port hole boxes superstructure
• leather ceilings
• lining > V-grooves, every 100mm, parallel to deckline/sheer
• access bolt connection for mounting superstructure
• drill holes and notches for assembly
• heating > add bulkhead penetrations for hose and grills
• FYI > solid corner profiles in furniture plintes will be painted white
• locker shelves > mounted with shelf supports (Hettich)
• sole > add hatches in combination with making the alu sole supports
• labels > create excel sheet with codes for each part
• ceilings > leather panels will be mounted with Fastmount
• hatches and portlights
  • Deckhatches:
    • Lewmar Size 60 low profile: 39960030
    • Lewmar Size 30 low profile: 39930030
  • Portligths in superstructure:
    • Lewmar Standard portlight Size 3: 393320200
  • Portlights in cockpit:
    • Lewmar Standard portlight Size 5: 393520200

Fore Cabin

• hatches in bed bottom > modify in way of batteries
• hatches bow thruster > enlarge
• shelf > add against FWD bulkhead, 300 deep, 650 from bed bottom
• shelf > add against AFT bulkhead, in corner with lining (for phone, etc)
• high lockers > move upper plinth outboard with 200mm
• shelf locker > move side panel 100mm forward
• porthole SB > relocate in middel of lining
• porthole PS > relocate? KMY
• shelf SB > rotate profile 10 degrees, move outboard to 10mm distance from vertical solid profile of shelf locker, make locker with doors under
• bed > make bulkhead in storage, forward of batteries
• bed > add bracket under each battery up to sole

Salon

• pillar mast bulkhead > connected with FB 8mm, split mast bulkhead
• table
• chain plate reinforcement > mask
• lower hinge in forward upper cabinet will be solved by KMY
• counter top > raise 100mm
• add shelf profile between upper lockers
• box against FWD bhd > bottle storage, make narrower, add hatch in counter top (with fingerhole)

Galley

• pillar behind removable side
• re-arrange front drawers to avoid collision with table
• fridge > mvoe down, drawer above fridge
• fridge > ventilation by holes in locker bottom next to plinth and holes in upper part of PS counter side (NO grill)
• countertop > raise 50mm
• shelf > add 1 or, if possible, 2 shelves between upperlockers. For spices, etc. Deep about 60mm and a high shelf profile of about 70mm
• upper lockers > LED lights behind solid profile? KMY
• drawers > use standard Hettich drawers where possible
• drawers in galley fore side > various heights, top about 80mm, second drawer about 200, third drawer about 300

Bathroom

• sole detail
• yard will inform if glass doors in bathroom will be applied or not
• material > panels can be normal HPL as rest of boat, the special quality W400-VV is canceled.
• entrance door > rotates outside and forward
• black water tank > 50 liter, behind toilet (shape to be determined by Navyk)
• glass doors > yard to decide to apply or not

Aft cabins

• PS > bulkhead cutout, profiles, raise horizontal profile in line with sole deckhouse
• bed bottoms > hatches for access storage space under, support?
• lining > align knuckles with V-grooves
• entrance door > rotates inside
• technical space > add access hatches in longitudinal panels

Deck house

• 'pillar boxes' to be moved outboard 10mm
• 'pillar boxes' add recesses for technical panels, dimensions? KMY
• all panels to be white, except for bench fronts, 'pillar boxes' besides entrance and top of guest cabin SB
• bench fronts and top of guest cabin to be covered with 6mm bamboo as for entrance doors
• add solid profiles around top of guest cabin.
• WJ will provide correct model of entrance
• add solid profiles at vertical corners of transition salon/guest cabin to deck house
• stairs > add solid profile to vertical corner of lower step
• recess behind seats > about 50 wide, 100 deep
• lining besides entrance > add solid profile at vertical (skewed) corner
• benches > seat width 550mm
• benches > back inclinated
• benches > raise bottom? KMY
• Aft cabin lining > reduce lost space behind lining
• Stair steps > use for storage (3 steps)
• Aft cabin top > removable plexiglass panel for light and air, detail? KMY
• PS bench > remove armrest, make suitable for transverse seating
• bed bottoms > raise 100mm for additional storage and wider matrass
• bed bottoms > hinged hatch
• bed PS > large drawer under

Sheet estimation

transverse grain

• 17mm single bamboo - 3 sheets - bench fronts SL / galley front / table sides
• 6mm single bamboo - 1 sheet - bench fronts DH

People

• Eeuwe Kooi - director/owner (not directly involved)
• Willem Berends - chain manger (responsible for contract)
• Willem-Jan van der Vegt - engineer (our contactperson)
• Haaie Andringa - foreman carpentry

Exchange work

• KMY negotiated €1.000 discount for delivering a 3D model of interior - send file is only a block file
• integration of heater ducting is not in contract
• info is not delivered on Monday, June 15 but came partially on June 16 and 17

As discussed

July 1, 2015

• furniture doors - 17mm is OK
• entrance hatch recess box - PUR insulated, put plywood panel in front
• stair steps solid wood
• cockpit sole - covered with cork 9mm
• lining - leather panels are canceled
• porthole boxes - yard makes tube, out of our delivery

June 16, 2015

• black water tank - to be determined by Navyk, volume around 50 liter, position SB behind toilet

June 11,2015

• tolerances
  • vertical:
    • sole to supporting structure - 0mm
    • ceiling to structure - 0mm
  • horizontal
    • clearance from inner frame contour - 20mm (space between frames is reserved for systems)
• insulation type is PUR
• grain orientation will be vertical
• sole supports are alu tube 50x30x?
• cabinet interiors to be white
• KMY workshop facilities:
  • no veneer press
  • edge band machine for straight edges
  • lamello machine
  • round router bits R6, R8, R10, R12
• Navyk will route the ducting for airheating through the interior
• Navyk is free to use their own material naming
• Navyk will give a price offer for the aluminium sole supports

Structure model - modifications!

• Forepeak bulkhead - stiffeners will be on aft side (cabin side)
• Pilothouse - between the windows will be a vertical T-profile with a web of 50x6 and a flange of 50x8
• Entrance door forecabin - to be determined by Navyk, it will be a joinery door, not an aluminum door
• sole structure - to be determined, Navyk will make a price offer for this