Difference between revisions of "General construction plan - small craft"
From NavykI
(→Outfitting) |
(→Structure) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
== General == | == General == | ||
*indicate what is not in delivery or what is yard delivery | *indicate what is not in delivery or what is yard delivery | ||
| − | *keep | + | *keep construction simple |
*use as little different plate thicknesses and profile sections as possible | *use as little different plate thicknesses and profile sections as possible | ||
*draw schematic | *draw schematic | ||
| + | *give all collected info | ||
*do NOT: | *do NOT: | ||
**insert SC planar groups | **insert SC planar groups | ||
| Line 31: | Line 32: | ||
*tank table | *tank table | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== Structure == | == Structure == | ||
| Line 53: | Line 49: | ||
**continuing structure (arrows) | **continuing structure (arrows) | ||
**profile snipes | **profile snipes | ||
| + | **principal limberhole detail | ||
| + | **principal welding scallop detail | ||
== Cut outs == | == Cut outs == | ||
| Line 73: | Line 71: | ||
*shaft installation | *shaft installation | ||
*thrusters (bow and stern): | *thrusters (bow and stern): | ||
| − | **indicate | + | **indicate inside AND outside diameter of tunnel |
**indicate maximum tunnel pipe length, for knuckled thruster tunnels show section with tube lengths | **indicate maximum tunnel pipe length, for knuckled thruster tunnels show section with tube lengths | ||
**indicate engine offset from CL | **indicate engine offset from CL | ||
**indicate engine angle | **indicate engine angle | ||
| + | **indicate hole pattern for thruster engine | ||
*deck drains | *deck drains | ||
*anchor arrangement | *anchor arrangement | ||
Latest revision as of 09:32, 8 December 2012
Contents
General[edit]
- indicate what is not in delivery or what is yard delivery
- keep construction simple
- use as little different plate thicknesses and profile sections as possible
- draw schematic
- give all collected info
- do NOT:
- insert SC planar groups
- use lines of Rhino solid model
Tables[edit]
- principal dimensions:
- Loa
- Lhull
- Lwl
- Boa
- Bwl
- Draft
- Displacement
- CE category
- hull speed
- construction:
- material properties
- classification
- principal scantlings
- drive train
- engine
- reduction box
- thruster bearing
- shaft details?
- propellor details?
- tank table
Structure[edit]
- principal frames
- bulkheads (WT bulkheads to be mentioned in frame title)
- webframes (mention in frame title)
- transom view
- centerline section OR side view
- bottom view
- deck view
- specify structure only 1 time:
- longitudinal structure in longitudinal views
- transverse structure in transverse views
- indicate:
- continuing structure (arrows)
- profile snipes
- principal limberhole detail
- principal welding scallop detail
Cut outs[edit]
- for every cut out
- location
- dimensions
- mark with crossed lines, linetype 'center'
- hatches and portholes:
- brand, model, HIP
- engine ventilation grill
Outfitting[edit]
- rudder construction
- rudder shaft installation
- steering system (cylinder support)
- engine girders
- thruster bearing plate
- shaft installation
- thrusters (bow and stern):
- indicate inside AND outside diameter of tunnel
- indicate maximum tunnel pipe length, for knuckled thruster tunnels show section with tube lengths
- indicate engine offset from CL
- indicate engine angle
- indicate hole pattern for thruster engine
- deck drains
- anchor arrangement
- bilge water collection point
- specify any equipment part which influences the delivery
- save data sheets of all used equipment in inbox
- make standard details for scallops, limber holes, breather holes, etc.
